Campbell-scientific NL200/NL201 Network Link Interface Instrukcja Użytkownika

INSTRUCTION MANUAL NL200/NL201 Network Link Interface Revision: 9/14 Copyright © 2011- 2014 Campbell Scientific, Inc.

Table of Contents iv

NL200/201 Network Link Interface 1. Introduction The NL200/201 Network Link Interface allows Campbell Scientific dataloggers and peripherals to comm

NL200/201 Network Link Interface 3.1 Physical Setup Using the supplied serial cable, connect the NL201’s CS I/O port to the datalogger’s CS I/O port.

NL200/201 Network Link Interface 3.2 Configuring the NL200/201 INSTALL THE DEVICE DRIVER BEFORE plugging the NL200/201 into your PC for the first ti

NL200/201 Network Link Interface An IPv4 address may look like 192.168.1.100:6785. An IPv6 address may look like [2001:db8::1234:5678]:6785. A fully

NL200/201 Network Link Interface 4. Overview The NL200/201 Network Link Interface is a device used to communicate with Campbell Scientific datalogger

NL200/201 Network Link Interface RS-232 serial server and a CS I/O serial server, an RS-232 serial server and a CS I/O PakBus router, an RS-232 PakBus

NL200/201 Network Link Interface Campbell Scientific’s LoggerNet software is used to communicate with the dataloggers once the NL200/201 is configured

NL200/201 Network Link Interface 5. Specifications General 177 g (6.3 oz) 16 x 6.73 x 2.54 cm (6.3 x 2.65 x 1 in) FIGURE 5-1. NL200/201

NL200/201 Network Link Interface Ethernet 10Base-T (full and half duplex), 100Base-TX (full and half duplex), Auto-MDIX Auto-IP (APIPA), IPv4, IPv6, I

NL200/201 Network Link Interface • Click OK. • Click Connect. • Configure the NL200/201 as needed for your application. • Click Apply to save your

NL200/201 Network Link Interface • Type edit and press Enter to edit the settings of the NL200/201. • As each NL200/201 setting is shown, press Ente

NL200/201 Network Link Interface routing table. These are devices that the NL200/201 has learned about through beaconing or allowed-neighbor lists. B

NL200/201 Network Link Interface However, an allowed neighbors list can be useful in restricting communication paths. • On the Network Services tab:

NL200/201 Network Link Interface FIGURE 7-1. PakBus® router LoggerNet setup 7.1.4 Connect You are now ready to connect to your datalogger using the

NL200/201 Network Link Interface the barrel-connector jack located on the edge of the device. (Note that an NL200 cannot be powered over CS I/O. An

NL200/201 Network Link Interface your settings are correct, you should see the current clock of your server and datalogger. FIGURE 7-2. Bridge mode

NL200/201 Network Link Interface 7.3.2 Configuring the NL200/201 RS-232 Serial Server • Connect to the NL200/201 in DevConfig (see Section 6, Config

NL200/201 Network Link Interface • You can verify your settings are correct by selecting the datalogger in the Network Map, selecting the Clock tab,

NL200/201 Network Link Interface connection, and data received on the TCP connection will be forwarded to the RS-232 port. This mode can be particula

Limited Warranty “Products manufactured by CSI are warranted by CSI to be free from defects in materials and workmanship under normal use and service

NL200/201 Network Link Interface In order to use TLS, the user must configure the NL200/201 with a user-supplied TLS Private Key and TLS Certificate.

NL200/201 Network Link Interface The settings found in the TLS Proxy Server and TLS tab in DevConfig are used to configure the NL200/201 TLS Proxy Ser

NL200/201 Network Link Interface datalogger and forward the unencrypted data. In HTTPS communications, web browsers use port 443. The NL200/201 will

NL200/201 Network Link Interface 7.6.2 DevConfig TCP Encrypted Communication to the NL200/201 In order to use DevConfig TCP Encrypted Communication

NL200/201 Network Link Interface 8.1.1 Configuring the NL200/201 • Connect to the NL200/201 in DevConfig (see Section 6, Configuring the NL200/201).

NL200/201 Network Link Interface 2. Check all your cables. • Verify that your Ethernet cable is securely plugged in between your NL200/201 and your

NL200/201 Network Link Interface communications is 6783. The default port number for RS-232 serial sever communications is 6784. The correct port nu

NL200/201 Network Link Interface • If running NL2xx firmware revision v.4 or greater, you can also type “eventloga” at the prompt to obtain an ASCII

NL200/201 Network Link Interface 28

Appendix A. Glossary Beacon Interval Devices in a PakBus® network may broadcast a hello-message to other devices in order to determine “neighbor” de

Assistance Products may not be returned without prior authorization. The following contact information is for US and international customers residing

Appendix A. Glossary Port Number A port number is a way to identify a specific process to which a network message is to be forwarded when it arrives

Appendix B. Cables, Pinouts, LED Function, and Jumper B.1 CS I/O The CS I/O cable is a 9-pin, straight-through cable with all 9 pins connected. Th

Appendix B. Cables, Pinouts, LED Function, and Jumper B.3 Ethernet The Ethernet 10Base-T/100Base-TX cable should be a Category 5 or better twisted p

Appendix B. Cables, Pinouts, LED Function, and Jumper B.6 LEDs TABLE B-6. Power LED State Description Off Device powered off On Device powered on

Appendix B. Cables, Pinouts, LED Function, and Jumper B-4

Appendix C. NL200/201 Settings All of the NL200/201 settings available from the Settings Editor in DevConfig are described below. C.1 Main Tab Mode

Appendix C. NL200/201 Settings When the device is configured in bridge mode, it is not possible to open a telnet session with it. CS I/O IP Interface

Appendix C. NL200/201 Settings IP Address The IP address uniquely identifies this node on an internet. If DHCP is enabled, this is the IP address o

Appendix C. NL200/201 Settings Ethernet Speed / Duplex Configuration Specifies the Ethernet link speed and duplex settings. Speed: When used as a TC

Appendix C. NL200/201 Settings connection with the remote server and if the connection fails to open, the device will continue to retry at an interva

Precautions DANGER — MANY HAZARDS ARE ASSOCIATED WITH INSTALLING, USING, MAINTAINING, AND WORKING ON OR AROUND TRIPODS, TOWERS, AND ANY ATTACHMENTS TO

Appendix C. NL200/201 Settings connection is functional as the device does not know the frequency or nature of the expected data. Set to 0 for no ti

Appendix C. NL200/201 Settings RS-232 TCP Serial Client Port This setting specifies the TCP port of the outgoing TCP Serial Client connection. (range

Appendix C. NL200/201 Settings detected for the timeout period. Set to 0 for no time-out (not recommended). (range 0..999) CS I/O PakBus Beacon Inte

Appendix C. NL200/201 Settings network. When a device has a neighbor list or neighbor filter setting filled in for a port, any device that has an ad

Appendix C. NL200/201 Settings PakBus Address Specifies the address that the route will reach. Response Time Specifies the amount of time (in mill

Appendix C. NL200/201 Settings Secure Proxy Forward Port Number. Also, regardless of this setting, the NL200/201 Secure Proxy Server will always lis

Appendix C. NL200/201 Settings TLS Proxy Timeout This setting, in units of seconds, will determine how fast the proxy server/client sessions will ti

Appendix D. Sending a New OS to the NL200/201 Whenever a new operating system is released for the NL200/201, it will be available from our website,

Appendix D. Sending a New OS to the NL200/201 3. Open DevConfig. 4. Select the NL200 under Device Type. 5. Ensure that the Use IP Connection box i

Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbe

Table of Contents PDF viewers: These page numbers refer to the printed version of this document. Use the PDF reader bookmarks tab for links to spec

Table of Contents 8. Applications..... 23 8.1 Working Around Firewalls ...

Table of Contents Tables B-1. CS I/O Pinout ..................... B-1 B-2. RS-232 Pino